How to Choose a Concrete Lifting Contractor in Utah: 6 Things to Check
Updated: Nov 11
Quick answer: A good concrete lifting contractor uses professional, high-pressure foam equipment and a load-bearing, high-density foam, not just a light void filler. They also fill and stabilize the soil under the slab and have the skill to lift it slowly and evenly, without cracking it.
By Drew Hubbard, owner of Utah Concrete Lifting and Repair in Mapleton, UT. Drew is a licensed General Contractor with 20+ years of construction experience. Updated October 2026.
Foam lifting looks simple from the curb: drill a few holes, inject foam, and the slab comes up. But the results depend a lot on who's doing it and what they're using. Here's the checklist I'd use if I were hiring someone to lift my own driveway, and how we stack up on each point.
1. Professional high-pressure equipment
Polyurethane lifting foam is made by mixing two liquid parts right at the job. To get a consistent, strong foam, they have to be heated and mixed at the right ratio under high pressure. That takes a real plural-component proportioner, not a handheld kit.
What to ask: "What kind of rig do you use to mix and pump the foam?"
How we do it: We run a hydraulic proportioner off our own diesel generator, so we're self-powered on site and don't need to plug into your house.
2. Load-bearing, high-density foam (not just void fill)
Some foams are made to fill empty space. Lifting foam has to carry weight: your car, your RV, or years of foot traffic. Ask what density of foam the contractor uses and whether it's made for lifting.
What to ask: "What foam do you use, and is it rated for lifting and load bearing?"
How we do it: We use a custom-made 3 lb hydrophobic polyurethane, made locally by Utah Foam Products. It's made in our area for our area, with blends designed for Utah soils. Hydrophobic means it repels water, so it won't wash out.
3. Soil stabilization, not just a lift
Concrete sinks because the soil under it washed out, settled, or was never packed well. A good lift fills the empty spaces under the slab and firms up that soil, so the slab is supported across its whole underside instead of sitting on a few high spots.
What to ask: "Do you fill the voids under the slab, or just raise it?"
How we do it: The foam spreads into the empty spaces under the slab and fills them as it lifts, so the slab ends up fully supported. If you want to know why Utah County concrete sinks in the first place, see Why Is My Concrete Sinking?
4. Skill and precision on the job
Lifting too fast or too far can crack a slab or push it out of line with the panels around it. The person on the hose matters. Ask who will actually do the work and how they control the lift.
What to ask: "Who will be on my job, and how do you keep from over-lifting or cracking the slab?"
How we do it: We're owner-operators, so the owners are on every job. We use specialized sensors for early movement and binding detection, so we can see when a slab starts to move or gets stuck before it becomes a problem. When a slab is bound up against another one, we have specialty saws that can cut concrete up to 15 inches thick to free it.
5. The right tools for hard-to-reach spots
Not every sunken slab is next to the driveway. Backyard patios, side yards, and pool decks can be a long way from the truck.
What to ask: "Can you reach my backyard or side yard?"
How we do it: We carry over 200 feet of hose, so we can reach backyards, side yards, and other hard-to-reach spots.
6. Straight answers on cost, timing, and warranty
A good contractor should tell you up front what to expect.
Cost: Lifting a typical sidewalk costs $300 to $1,200, and a driveway panel typically costs $300 to $800, depending on size and how far it has to come up. There's no minimum job charge, and a fuel fee can apply for remote jobs. Our Utah concrete lifting cost guide has the details.
Cure time: You can walk on it right away. Keep vehicles off for at least 4 hours, and up to 24 hours.
Weather: In winter, we lift only when it's above 40°F and the slab is clear of snow and ice.
Warranty: Ask what's covered and for how long, and get it in writing.
Quick checklist
What to check | Why it matters | Utah Concrete Lifting and Repair |
|---|---|---|
Equipment | Consistent, strong foam | Hydraulic proportioner, self-powered with a diesel generator |
Foam | Must carry weight and resist water | Local 3 lb hydrophobic foam from Utah Foam Products |
Soil support | Keeps the slab from sinking again | Foam fills the empty spaces under the slab |
Crew | Even lift without cracking | Owner-operators with movement and binding sensors |
Reach | Backyards and side yards | Over 200 feet of hose |
Experience | Knows concrete and soil | 20+ years of construction experience |
Hiring a concrete lifting contractor: FAQ
Is foam lifting better than mudjacking?
For most Utah County jobs, yes. Foam is lighter, uses smaller holes, and you should keep vehicles off for at least 4 hours, and up to 24 hours. Our polyjacking vs. mudjacking guide explains the differences.
How long until I can use my driveway?
You can walk on it right away. Keep vehicles off for at least 4 hours, and up to 24 hours.
Is there a minimum charge?
No. There's no minimum job charge, so a single sidewalk square is worth a call.
Should I lift my slab or replace it?
Many sunken slabs that are still in one piece can be lifted. See Should I Lift or Replace My Sunken Concrete? for how to tell.
More answers are on our concrete lifting FAQ page.
Get a free estimate
If you've got a sunken driveway, sidewalk, patio, or steps anywhere in Utah County, call or text (385) 398-9886 or chat with us for a free estimate.
Drew Hubbard, Utah Concrete Lifting and Repair
1565 West Park Meadows Drive, Mapleton, UT 84664 · (385) 398-9886

Comments